It requires a Mac OS (9/X) and PowerPC computer. Remove boot loader out of memory problemMac-on-Linux (MOL) allows you to run MacOS 9 and MacOS X from within Linux. For Linux and macOS, run the lnx-install.sh or osx-install.sh files under root (not.See AddingRepositoriesHowto for more information.This can be done using Synaptic Package Manager or by running the following commands sudo apt-get install molSudo apt-get install mol-drivers-macosx # for MacOS XSudo apt-get install mol-drivers-macos # for MacOS 9If you are not comfortable with editing text look at NanoHowto.This assumes that you have a working install of Mac OS X or 9, on a partition on you harddrive somewhere.There are a few settings you may want to play with be for you use mol. It is also possible to use MOL to install MacOS into a disk image, see man mol for more details.The MOL kernel modules are included in DapperDrake so it is no longer necessary to compile and install them manually.To install all of Mac-on-Linux, you'll need to enable the universe and multiverse, see AddingRepositoriesHowto for details.You will need to install the following packages mol and mol-drivers-macosx and/or mol-drivers-macos for MacOS X and/or MacOS 9 support.You may need to add this repository to get some of the drivers: woody/. See for full details.This howto assumes that you have a working install on MacOS on your computer.
You need to install the MOL package that you find on the desktop. The following command makes sure you can run Mac-on-Linux as a normal user.Sudo dpkg-statoverride -update -add root root 4755 /usr/lib/mol/bin/molNow you should be able to run startmol -osx (just startmol for Mac OS 9), and Mac OS X will boot up in a window or on a new virtual terminal. If you get a random mess, blank screen or some other problem then press 'n'By default, Mac-on-Linux requires root privileges to run. The red screen comes out as a stripes, but it seems to work anyway. (It may also crash if you give too much RAM I had to keep a ram_size of 48 in my molrc.macos.)Then it is worth setting up the video modes, run sudo molvconfigYou basically type 'y' to try out a configuration, and then 'y' if you can see a nice gradient on the screen. Norton internet security for mac comcastMine was given as follows: 6: tun0: mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 100Inet6 fe80::d868:17ff:fe7b:32c1/64 scope linkIn OS X, then set up the en3 network port manually, by allocating an appropriate IP (in my case 192.168.40.2 was a good choice), set Router and DNS server to the ip associated with your tun0 interface in linux (192.168.40.1) and the subnet mask to 255.255.255.0. Once you have completed the setup, run ip addr to check the ip address for the tun0 interface. Make sure that en3 is set to configure with DHCP.Now open up Safari or Firefox, and if you are lucky you should have a web connection.Do as above, but without installing dhcpd. MOL creates a network tunnel called tun0 at the Linux end, and en3 on the Mac OS X end.Once you have logged into to Mac OS X open up the system preferences. CTRL + ALT + F7 should take you back to your Linux desktop.If you want mol to always start full screen, edit /etc/mol/molrc.video and change enable_xvideo: yes to enable_xvideo: noSee its manpage for more usage information.If you are using mol to use the iTunes music store, or watch flash on the web, then you will need to get networking running.You will need to install ipmasq, dnsmasq and dhcpd using synaptic orSudo apt-get install ipmasq dnsmasq dhcpdThen enable dhcp for the tun0 interface that mol uses, in /etc/default/dhcp, put the lineAnd in /etc/mol/tunconfig at the bottom just beforeNow run startmol -osx, and we can set up the network on the Mac OS X side. To do that, I am providing my notes below.To run Tiger and Eliminate Annoying Sluggish Behavior on MOL Install this Patched VersionThanks to folks on the MOL mailing list for these tips. Afterwards, the response was more snappy.) The real fix is to use a more recent version of Mac-on-Linux though. (Before I did this I was unable to even double click. Then you need to go to the sound control panel and enable the MOL Audio for output. Your OSX boot partition should not be mounted under linux and should have the setting of blkdev /dev/hda3 -boot -rwObviously the hda3 part could be different for you.OS 9 Double Click and Slow Response TroubleIf you are having very slow response with OS 9, you probably need to open the MOL Install CD that appears on the desktop and drag the MOLAudio to the System Folder. Linux Based Emulator Download The PatchedActually, I had better luck on the networking setup with the sheep driver. Look for the latest mol version he has provided.6) Set up and start MOL using the instructions in the section above. 3) Download the patched MOL that Joe Jezak has kindly provided. You can also use the synaptic package manager or Adept to do this.2) Follow the instructions on this Wiki for building the kernel found at. Mine was 2.6.12-9-powerpc. You can user uname -r to determine your version. You will need to do this as root. If I figure that out, I'll append this note.If you start MoL to boot OS X and get an error that looks like this: > -> Boot loader failure: Out of memoryThen you need to install the new boot loader.3) Copy the file into /usr/share/mol/drivers/. With this setting Tiger boots and gets an IP address via dhcp from my local wireless router.A side note: I have not been able to boot an OS 9 partition with this setup and there have been some similar notes on a Yellow Dog Linux forum.
0 Comments
Leave a Reply. |
AuthorLori ArchivesCategories |